资源列表
排序选择:
[单片机(51,AVR,MSP430等)] 单片机实验二参考资料
说明:利用51单片机实现唱歌,使用C语言编程,而且还有学号的实现(Temperature sensing by 51 single chip microcomputer)<丽丽暗暗> 在 2025-09-20 上传 | 大小:19.27mb | 下载:0
[WEB源码] crossphp_v1.6.1
说明:crossphp开发框架是一个简洁高效,轻量易扩展的PHP5.3+ 开发框架。(The crossphp development fr a mework is a simple, efficient, lightweight, extensible PHP5.3+ development fr a mework.)<憨头> 在 2025-09-20 上传 | 大小:103kb | 下载:0
[其他小程序] 实验1 - GPIO驱动LED
说明:艾克姆开发板例程,驱动GPIO点亮led(ACM development board routines, drive GPIO to light LED)<昵称语法煞笔> 在 2025-09-20 上传 | 大小:1.13mb | 下载:0
[WEB源码] wzzzjlq_v1.3
说明:网站蜘蛛记录器是由蓝途工作室独立开发的又款免费程序.主要功能是记录各大搜索引擎对网站采集情况.实时记录百度,谷歌蜘蛛的爬行轨迹,分析.达到更好的优化网站的目的。(Web spider recorder is a free program developed by the Blue Road studio independently. The main function is to record the collection situation of the major search engine<憨头> 在 2025-09-20 上传 | 大小:40kb | 下载:0
[人工智能/神经网络/遗传算法] matlab codes for detectors
说明:BPSK with Maximal ratio combining<Hackerguy> 在 2025-09-20 上传 | 大小:5kb | 下载:0
[单片机(51,AVR,MSP430等)] TinyWireS
说明:wire libraryWire协议总线通信中最为重要的一种操作,在每次总线通信之前主机必须首先发送复位信号。如程序1.1所示,产生复位信号时主机首先将总线拉低480~960μs然后释放,由于上拉电阻的存在,此时总线变为高电平。(Wire protocol, the operation of the most important of a kind of bus communication, the host before each bus communication must first se<lsj8023> 在 2025-09-20 上传 | 大小:8kb | 下载:0
[单片机(51,AVR,MSP430等)] Firmata
说明:wire libraryWire协议总线通信中最为重要的一种操作,在每次总线通信之前主机必须首先发送复位信号。如程序1.1所示,产生复位信号时主机首先将总线拉低480~960μs然后释放,由于上拉电阻的存在,此时总线变为高电平。(Wire protocol, the operation of the most important of a kind of bus communication, the host before each bus communication must first se<lsj8023> 在 2025-09-20 上传 | 大小:230kb | 下载:0
[其他小程序] PN532_I2C
说明:wire libraryWire协议总线通信中最为重要的一种操作,在每次总线通信之前主机必须首先发送复位信号。如程序1.1所示,产生复位信号时主机首先将总线拉低480~960μs然后释放,由于上拉电阻的存在,此时总线变为高电平。(Wire protocol, the operation of the most important of a kind of bus communication, the host before each bus communication must first se<lsj8023> 在 2025-09-20 上传 | 大小:2kb | 下载:0
[单片机(51,AVR,MSP430等)] PinChangeInt-master
说明:arduino的引脚是已经定义了的。如,我在51上模拟arduino的方式写的就是0是P00,27就是P27。然后用digitalWrite(0,HIGH)方法来让P00引脚置1。因为sbit类型的引脚位定义是不能作为参数传递的。(Arduino pins is already defined. For example, I wrote on the 51 of the method of simulation arduino is 0 is P00, 27 is P27. Then use d<lsj8023> 在 2025-09-20 上传 | 大小:49kb | 下载:0
[matlab例程] Design_curve
说明:Design curve for microwave crossover in MATLAB.<Bazz> 在 2025-09-20 上传 | 大小:2mb | 下载:0