资源列表
[其他小程序] ansys5
说明:利用ansys计算的应力结果,求出截面内力,再利用材料力学公式求等效应力(此例是求坝基面的等效应力)-ANSYS calculated using the stress results, obtained cross-section of internal forces, and then use the formula for the mechanical equivalent stress (in this case is to strive for the dam foundation s<姚艳华> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[人工智能/神经网络/遗传算法] firbynna
说明:此程序为本人编写的神经网络法设计1型FIR滤波器的程序,读者读此程序后,可以很深刻地理解如何用BP网络和LMS算法来设计滤波器。 只需更改程序中的H值,即可生成各种低通,高通,带通,带阻滤波器。程序运行结果可得到滤波器系数,幅频曲线和衰减曲线。 可通过更改迭代步长和误差极限来调整滤波器特性。-I prepared for this procedure the neural network type 1 FIR filter design procedures, the reader a<黄翔东> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[matlab例程] cazhi
说明:各种插值方法的效果比较 线性内插法,内插法,三次多项式内插法,多项式拟合法 将这些内插的结果及原先的采样点画在同一个图 -The effect of various interpolation methods compared linear interpolation, interpolation, cubic polynomial interpolation, polynomial fitting interpolation of these results and the ori<zhouliyong> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[2D图形编程] CalcQieDian
说明:过圆外一点求一个与圆相切的圆的切点,切园的半径已知-Round-off point outside the circle for a circle tangent to the cut-off point, cut park known radius<李智信> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[2D图形编程] CalcQieDian2
说明:圆心(a,b),半径r 圆外一点坐标(m,n) 求其切点的坐标(x,y)-Center of a circle (a, b), outer radius r circle point coordinates (m, n) for its cut-point coordinates (x, y)<李智信> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[2D图形编程] CalcQieDian3
说明:三点A,B,C (坐标A.x, A.y ......) A、B是矩形的两端点 且C在与AB平行的 矩形另一边上 或其延长线上 求矩形另外两端点M、N 再求与MN夹角为45度,与M距离为10的点P 以及与MN夹角45度,与N距离为10的点Q 注:P、Q都在矩形内部 -Three points A, B, C (coordinates Ax, Ay ......) A, B is rectangular and the two end points of C<李智信> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[数据结构常用算法] Greedy_DelleteNumber
说明:using greedy tratage to solve the problem of Number Delete.<tony chen> 在 2026-01-23 上传 | 大小:1kb | 下载:0
[图形图像处理(光照,映射..)] Tschebyscheff
说明:Tschebyscheff滤波器设计,包括零极点分布,幅值相位的关系。-Tschebyscheff filter design, including the zero-pole distribution, the amplitude-phase relationship.<郑勉> 在 2026-01-23 上传 | 大小:1kb | 下载:0