资源列表

« 1 2 ... .28 .29 .30 .31 .32 215433.34 .35 .36 .37 .38 ... 216384 »

[单片机(51,AVR,MSP430等)DS18B20

说明:AVR控制DS18B02的程序接口!可以直接使用该程序控制它,采集当前的数据!-AVR control procedures DS18B02 interface! Can directly use the control it, and collecting current data!
<廖晶晶> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[VHDL编程seg7_1

说明:用VHDL描述一个让6个数码管同时显示的控制器,同时显示0、1、2、3、4、5这6个不同的数字图形到6个数码管上,输入时钟调节频率,使得能够观察到稳定显示的6个数字。可异步复位-Using VHDL descr iption of a six digital tube display controller at the same time, also showed that six different 0,1,2,3,4,5 digital graphics to six digital tub
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[VHDL编程zmd_1

说明:用VHDL描述一个由8个发光二极管组成的走马灯。有系统复位。单点移动模式:一个点在8个发光二极管上来回的亮。幕布式:从中间两个点,同时向两边依次点亮直至全亮,然后再向中间点灭,依次往复。采用拨码开关转换显示模式。 -Use VHDL to describe an 8-digit LED lantern. System has reset. Single point of mobile model: a point in eight light-emitting diode on the li
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[VHDL编程zmd_1

说明:用VHDL描述一个由8个发光二极管组成的走马灯。有系统复位。单点移动模式:一个点在8个发光二极管上来回的亮。幕布式:从中间两个点,同时向两边依次点亮直至全亮,然后再向中间点灭,依次往复。采用采用一个按键转换显示模式。 -Use VHDL to describe an 8-digit LED lantern. System has reset. Single point of mobile model: a point in eight light-emitting diode on the
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[matlab例程AMI

说明:产生AMI码,并求其功率谱密度和时域波形。 -AMI generated code, and for its power spectral density and time-domain waveform.
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[matlab例程U_PCM

说明:格式 [sqnr,a_quan,code]=u_pcm(a,n) 输入样值序列a 、量化电平数目n, 程序计算量化间隔、进行均匀量化、进行编码、计算量化信噪比, 返回量化信噪比squn、编码前的量化序列a_quan、编码后的码序列code。 -Format [sqnr, a_quan, code] = u_pcm (a, n) input sample value sequence a, the number of quantization levels n, the calculati
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[数值算法/人工智能MAZI

说明:设定a为N(0,1)的500个随机数和量化级数n=64, 调用u_pcm.m, 分别输出sqnr、a(1:5)、a_quan(1:5)、code(1:5,:)。 -Set a for the N (0,1) of 500 random numbers and quantify the series n = 64, call u_pcm.m, respectively output sqnr, a (1:5), a_quan (1:5), code (1 : 5,:).
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[数值算法/人工智能wucha

说明:设定a为N(0,1)的500个随机数和i长为500,以n=8、16、64.分别调用u_pcm.m ,从中计算量化误差f=a-a_quan并绘图,分别输出各样值的量化误差图形。 -Set a for the N (0,1) of 500 random numbers and i long for the 500 to n = 8,16,64. Were called u_pcm.m, quantization error from the calculation of f = a-a_quan
<wx> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[教育/学校应用nob_new

说明:在毕业设计中用到的画图的程序 觉得挺有用的-Graduation design drawing used in the procedure used to feel quite
<tyh> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[操作系统开发zhucunfenpeiyuhuishou

说明:实现模拟操作系统运行时的主存空间的分配与回收-Realize operating system run-time simulation of the main memory space allocation and recovery
<jim> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[matlab例程myMM1

说明:刚写的Matlab下的M/M/1排队的仿真代码,加了完整的注释-Just write the M/M/1 queue under Matlab simulation code, plus a complete Notes
<阿哲> 在 2025-06-26 上传 | 大小:1kb | 下载:0

[游戏zhuang

说明:一个小游戏,简介:在开始运行该程序时,会出现两个动画人物的脸,按任意键 后这两个脸会来回相撞5次,(在这5次期间会有相应的文字和图形输出,比如:会有旋转时针控制时间的延迟...)。完了后,会输出一行提示信息:按回车键,这两个脸会做三个逆时针360度的旋转,按ESC键,会退出该程序,按任意键,他们会再次相撞。-A small game Descr iption: Run this program in the beginning, the system would create two anima
<陶彬> 在 2025-06-26 上传 | 大小:1kb | 下载:0
« 1 2 ... .28 .29 .30 .31 .32 215433.34 .35 .36 .37 .38 ... 216384 »

源码中国 www.ymcn.org