资源列表

« 1 2 ... .70 .71 .72 .73 .74 25075.76 .77 .78 .79 .80 ... 33928 »

[单片机(51,AVR,MSP430等)I2C

说明:I2C总线驱动程序,供单片机学习者借鉴。-I2C bus driver for the SCM learners learn.
<小周> 在 2025-06-05 上传 | 大小:4kb | 下载:0

[单片机(51,AVR,MSP430等)Car-alarm

说明:单片机实现的汽车防盗器设计,可应用于简单的汽车报警防盗系统中-Microcontroller car alarm design, can be applied to a simple anti-theft car alarm system
<小周> 在 2025-06-05 上传 | 大小:19kb | 下载:0

[单片机(51,AVR,MSP430等)Wireless-Serial-Communication

说明:实现单片机的无线串口通信,希望对各位单片机学习者能有所帮助。-The wireless serial communication SCM, SCM learners hope you can help.
<小周> 在 2025-06-05 上传 | 大小:11kb | 下载:0

[VHDL编程VHDL-translation-in-Russian

说明:VHDL translation in Russian
<SHUR!K> 在 2025-06-05 上传 | 大小:6.54mb | 下载:0

[单片机(51,AVR,MSP430等)SIP_master_slave

说明:这是一个基于AVR16系列的SPI寄存器通信的源程序,本文件有MASTER与SLAVE两种文件,分别用于主从机间的通信-This is a series based on AVR16 SPI communication register of the source, the files have MASTER and SLAVE two documents, one for communication between master and slave
<赵集> 在 2025-06-05 上传 | 大小:35kb | 下载:0

[VHDL编程Lab07_DigitalLock

说明:Design and Implementation of a vhdl based Digital Lock
<getsatish_hyd> 在 2025-06-05 上传 | 大小:163kb | 下载:0

[VHDL编程FPGA-IIC

说明:利用VHDL实现延时程序 很不错的资料 适合学习CHDL-Delay procedure using VHDL implementation very good information for learning CHDL
<qzl001> 在 2025-06-05 上传 | 大小:235kb | 下载:0

[DSP编程esay5509

说明:5509开发板附带程序,包含FIR滤波器,FFT等内容,说明详细-5509 board which contains FIR FFT and so on
<Jack> 在 2025-06-05 上传 | 大小:296kb | 下载:0

[Windows CEtestcurve_2D

说明:这是一个wince环境下的画曲线的程序,在EVC环境中编译使用-This is a wince of a curve under the procedures, compiled with the environment in the EVC
<Lee> 在 2025-06-05 上传 | 大小:3.43mb | 下载:0

[uCOS开发uCOS_UCGUI(2.8)

说明:金牛开发板程序,在KeilC的环境中使用,这是ucos2的程序-Taurus Development Board procedures used in KeilC environment, this is the procedure ucos2
<Lee> 在 2025-06-05 上传 | 大小:3.25mb | 下载:0

[单片机(51,AVR,MSP430等)8_ethernet

说明:LPC2103以太网程序,开发环境是KeilC-LPC2103 serial procedures, the development environment is KeilC
<Lee> 在 2025-06-05 上传 | 大小:284kb | 下载:0

[单片机(51,AVR,MSP430等)trick-lock

说明:电子密码锁: 可设定从1位到8位的密码,从键盘键入正确密码才可更改密码或开锁。输入三次错误密码电路就不断报警。开锁信号输出口用发光二极管表示。 1.可设置密码,掉电密码能保存; 2.按键确实被按下时发出一下提示音; 3.设置新密码前需校验旧密码; -Electronic code lock: can be set from 1-8 in the password from the keyboard to type the correct password to change
<jy> 在 2025-06-05 上传 | 大小:47kb | 下载:0
« 1 2 ... .70 .71 .72 .73 .74 25075.76 .77 .78 .79 .80 ... 33928 »

源码中国 www.ymcn.org