文件名称:sl200
- 所属分类：
- 嵌入式/单片机编程
- 资源属性：
- [C/C++] [源码]
- 上传时间：
- 2012-11-26
- 文件大小：
- 1.05mb
- 下载次数：
- 0次
- 提 供 者：
- zhouyo******
- 相关连接：
- 无
- 下载说明：
- 别用迅雷下载，失败请重下，重下不扣分！
介绍说明－－下载内容均来自于网络，请自行研究使用
门磁开喇叭工作，（可立即工作，或延时工作)延时可选由跳线选
择(0s ,10s,30s,60s)(工作时间为1M，3M，15M长期)报警状态，门磁关不停止必须由外面锁头控制停止，或待机standy
锁开关OFF 喇叭停止工作，断电
开关ON时自检若门磁或防拆没有闭合时不进入待机LED 常亮，若一
切正常进入待机 喇叭进入STandby 模式standby状态，用1LED闪烁指示
-Open door magnet speakers work (work immediately, or delay the work) by the jumper selectable delay options (0s, 10s, 30s, 60s) (working hours 1M, 3M, 15M long) alarm status, door magnetic relations do not stop the lock from the outside must be controlled to stop, or stand-standy lock switch OFF horn to stop working, self-test if the power switch ON, there is no closed door magnet or tamper LED light is not going into standby, if all the speakers into the normal standby STandby mode standby status, with 1LED flashing instructions
择(0s ,10s,30s,60s)(工作时间为1M，3M，15M长期)报警状态，门磁关不停止必须由外面锁头控制停止，或待机standy
锁开关OFF 喇叭停止工作，断电
开关ON时自检若门磁或防拆没有闭合时不进入待机LED 常亮，若一
切正常进入待机 喇叭进入STandby 模式standby状态，用1LED闪烁指示
-Open door magnet speakers work (work immediately, or delay the work) by the jumper selectable delay options (0s, 10s, 30s, 60s) (working hours 1M, 3M, 15M long) alarm status, door magnetic relations do not stop the lock from the outside must be controlled to stop, or stand-standy lock switch OFF horn to stop working, self-test if the power switch ON, there is no closed door magnet or tamper LED light is not going into standby, if all the speakers into the normal standby STandby mode standby status, with 1LED flashing instructions
(系统自动生成,下载前可以参看下载内容)
下载文件列表
sl200门磁延时\sl200门延时1\sl200c\makefile
.............\............\......\Obj\sl200.asm
.............\............\......\...\sl200.asm.as
.............\............\......\...\sl200.asm.as.dep
.............\............\......\...\sl200.asm.dat
.............\............\......\...\sl200.o
.............\............\......\...\sl200c.map
.............\............\......\...\sl200c.plo
.............\............\......\...\sl200c.rpt
.............\............\......\...\sl200c.sn8.dep
.............\............\......\sl200.asm
.............\............\......\sl200.asm.as
.............\............\......\sl200.asm.as.dep
.............\............\......\sl200.asm.dat
.............\............\......\sl200.c
.............\............\......\sl200.c.dep
.............\............\......\sl200.o
.............\............\......\sl200c.cfg
.............\............\......\sl200c.cop
.............\............\......\sl200c.map
.............\............\......\sl200c.msk
.............\............\......\sl200c.out
.............\............\......\sl200c.plo
.............\............\......\sl200c.prj
.............\............\......\sl200c.prj.dbg
.............\............\......\sl200c.sn8
.............\............\......\sl200c.sum
.............\............\......\sl200c_inc.h
.............\............\......\sl200w.c
.............\............\......\_sl200c.cfg
.............\............\......\_sl200c.cop
.............\............\......\_sl200c.msk
.............\............\......\_sl200c_inc.h
.............\............\SL600新.wsp
.............\............\SL600新.wsp.bkp
.............\............\SL600新.wsp.dep
.............\............\SN8P2501B_V13_SC.pdf
.............\SL200门延时报警..PCB
.............\sl200门延时报警器.PCB
.............\...........1\sl200c\Obj
.............\............\sl200c
.............\sl200门延时1
sl200门磁延时
.............\............\......\Obj\sl200.asm
.............\............\......\...\sl200.asm.as
.............\............\......\...\sl200.asm.as.dep
.............\............\......\...\sl200.asm.dat
.............\............\......\...\sl200.o
.............\............\......\...\sl200c.map
.............\............\......\...\sl200c.plo
.............\............\......\...\sl200c.rpt
.............\............\......\...\sl200c.sn8.dep
.............\............\......\sl200.asm
.............\............\......\sl200.asm.as
.............\............\......\sl200.asm.as.dep
.............\............\......\sl200.asm.dat
.............\............\......\sl200.c
.............\............\......\sl200.c.dep
.............\............\......\sl200.o
.............\............\......\sl200c.cfg
.............\............\......\sl200c.cop
.............\............\......\sl200c.map
.............\............\......\sl200c.msk
.............\............\......\sl200c.out
.............\............\......\sl200c.plo
.............\............\......\sl200c.prj
.............\............\......\sl200c.prj.dbg
.............\............\......\sl200c.sn8
.............\............\......\sl200c.sum
.............\............\......\sl200c_inc.h
.............\............\......\sl200w.c
.............\............\......\_sl200c.cfg
.............\............\......\_sl200c.cop
.............\............\......\_sl200c.msk
.............\............\......\_sl200c_inc.h
.............\............\SL600新.wsp
.............\............\SL600新.wsp.bkp
.............\............\SL600新.wsp.dep
.............\............\SN8P2501B_V13_SC.pdf
.............\SL200门延时报警..PCB
.............\sl200门延时报警器.PCB
.............\...........1\sl200c\Obj
.............\............\sl200c
.............\sl200门延时1
sl200门磁延时