搜索资源列表
Precision-CNC-Power
- 高精度数控电源，可以数字控制输出0-12V，步进0.1V效果好，纹波小。-High-precision numerical control power can be digitally controlled output 0-12V, step 0.1V effect, small ripple.
Sq-inverter-sch
- 12V quasi sinewave inverter schematics in protel
sq-inverter-pcb
- 12V quasi sine wave inverter pcb design in protel
BUCK1
- buck 的matlab仿真，进行PID反馈调整，输入12v，输出5v-matlab buck
T6322A
- 是一款降压型LED恒流驱动IC，SOT23-6封装，，输入电压为5到38V，输出电流最大为1A，效率高达97 ，含有PWM调光功能。主用在12V/24V LED MR16恒流板，LED手电筒板，LED背光驱动等等产品上-A buck type constant current LED driver IC, SOT23-6 package, input voltage of 5 to 38V, output current up to 1
BUCK-circuit--feedback-loop-design
- 开关电源设计：一个28V 输入12V/4A 输出的电源 电压输入范围:： 20~30V 额定输出电压： 12V 输出纹波： 125mV（1 ）-Switching power supply design: a 28V input 12V/4A output power Voltage input range:: 20 ~ 30V Rated output voltage: 12V Output Ripple: 1
drive-stepping-motor-
- 这款步进电机的驱动电压12V，步进角为 7.5度 . 一圈 360 度 , 需要 48 个脉冲完成!!! 该步进电机有6根引线，排列次序如下：1:红色、2:红色、3:橙色、4:棕色、5:黄色、6:黑色。 采用51驱动ULN2003的方法进行驱动。 -The stepping motor has six of the lead, rankings are as follows: 1: red, 2: red, 3:
High-Voltage-Generator
- 基于UC3845的高压发生电路，将12V转化为400V的高压模块。-This source can used to design a high-voltage supply by used the chip of UC3845.
SD-50
- 可以产生5v、12v/4a的稳压电源模块-failed to translate
pic16f684spwm
- 用pic16f684产生spwm信号 驱动4个场管生成正弦波 做12v 到 220v 的逆变器用。-12v to 220 v spwm
Variable-Power-Supply
- VARIABLE POWER SUPPLY USING A FIXED-VOLTAGE REGULATOR IC..Avoltage regulator (also called a ‘regulator’) with only three terminals appears to be a simple device, but it is in fact a very complex integrated circ
4523748564
- +12V -12V +5V -5V 电源+电路图+pcb图。-+12 V-12V+5 V-5V power supply+ schematic
shukongdianyuan
- 数控电源，包括程序，原理图，PCB图。步进值为0.1V ，可调范围为0V~12V。-NC power, including the procedures, schematics, PCB map. Stepping is 0.1V, and adjustable range of 0V ~ 12V.
intellectual-car
- 简易智能迷宫小车的控制系统以STC89C52为核心，用一片L298N驱动两个减速电机。12V电源单独给电机供电，再用7805把12V电源降压至7V给单片机供电。小车的传感器模块感应壁障，并将壁障信号输入最小系统版，最小系统版根据程序设计的要求做出相应的判断送给电机驱动模块，让小车来实现前进、左转、右转、反转等基本功能。-Simple intelligent control system of the labyrinth car S
AD620
- ad623 是一个集成单电源仪表放大器，它能在单电源( + 3v～ + 12v) 下提供满电源幅度的输出,ad623 允许使用单个增益设置电阻进行增益编程,以得到良好的用户灵活性。在无外接电阻的条件下,ad623 被设置为单位增益 外接电阻后,ad623 可编程设置增益,其增益最高可达1000 倍。-Ad623 is a integrated single power instrument amplifier, it can in a
3W4C
- 三线四回路，电压：12V和24V，有闪动，流水，渐变，变速的效果。要交流电压。-Four three-wire circuit, voltage: 12V and 24V, flashing, flowing water, gradient, variable speed. To the AC voltage.
pull_push_converter_up
- 推挽电路 升压电路，用于车载逆变器，能将电压从12V正激到350V-The push-pull circuit step-up circuit for in-vehicle inverter, can forward voltage from 12V to 350V
an144_files
- CodeLockAVR electronic combination lock is realised with Atmel AVR microcontroller AT90S2313. Program in hex code is 2 kB long. User code is consisted of 1 to 4 digits. If the code is entered in the correct sequenc
LC
- 本系统是以FPGA（EP2C8Q240C8）为控制核心，由压控振荡器、PLL倍频器、高频功率放大器、遥控器及LCD显示模块组成的压控LC振荡器。能实现输出正弦波频率在15MHZ~35MHZ步进可调，其最小步进为5002HZ，频率稳定度为10-5。当输出信号的频率为30MHZ、峰峰值稳定在1V左右时，在+12V单电源工作的情况下，功率放大器能实现在50Ω纯阻性和50Ω+20pf容性负载上输出功率大于20mw。LCD显示模块能实时显示输出信
24BYJ48-12V
- 四相八步驱动的步进电机资料与程序，应用在多方面的产品，比如空调摆风里面。-Four eight-step phase drive stepping motor data and procedures used in a wide range of products, such as air conditioning put the wind inside.