搜索资源列表
ctc_int
- Example of programming 82C54 timerswith 82C59 interrupt controller This example uses CTC channel 0 to monitor a tachometer type pulse input. The CTC is set to generate an interrupt for every 5 pulses which in the exampl
ISD4000
- isd4002语音模块，51单片机控制程序，多段录放时，确定录、放音的地址方法：.利用rac脚的脉冲。录音时，每过一个地址，rac会输出一个低脉冲。通过计数器来记录这个脉冲数，就知道录音时用了多少个地址。 就得出了这段语音的地址。 2.miso脚会输出当前地址。查询miso的返回值即可。 -isd4002 voice module 51 microprocessor control program, multi playback
CheckSpeed
- 用单片机设计的测速表源程序，测量转速，使用霍尔传感器，被测轴安装有12只磁钢，即转轴每转一周，产生12个脉冲，要求将转速值（转/分）显示在数码管上。-Speed table with a single chip design source, measurement speed, use the Hall sensor, measured shaft equipped with 12 magnets, which turns a shaf
freqmeter
- C8051F340 测频率，脉冲数，占空比，加128×64液晶频，测试通过了-C8051F340 measuring frequency, pulses, duty cycle, plus 128 × 64 LCD frequency, test passed
step_motor
- 步进电机是一种能够将电脉冲信号转换成角位移或线位移的机电元件，它实际上是一 种单相或多相同步电动机。单相步进电动机有单路电脉冲驱动，输出功率一般很小，其用途 为微小功率驱动。多相步进电动机有多相方波脉冲驱动，用途很广。使用多相步进电动机时， 单路电脉冲信号可先通过脉冲分配器转换为多相脉冲信号，在经功率放大后分别送入步进电 动机各相绕组。每输入一个脉冲到脉冲分配器，电动机各相的通电状态就发生变化，转子会 转过
PulsedOFDM
- In this paper, we describe a novel approach for reducing the power consumption and complexity of a multiband orthogonal frequency-division multiplexing (MB-OFDM) ultrawideband (UWB) system by applying ideas from pulsed U
HigherOrderGaussianPulseForUWB
- These matlab codes are for UWB and Higher order Gaussian pulses.-These matlab codes are for UWB and Higher order Gaussian pulses.
soliton
- 采用分步傅里叶方法对NLSE 进行了求解，并在归一化和功率补偿条件下模拟和分析了输入脉冲为双曲正割脉冲，高斯脉冲，超高斯脉冲传输对比情况，以及一到三阶双曲正割光脉冲条件下光脉冲传输演变情况-Using split-step Fourier method NLSE was solved, and in the normalization and power compensation under simulation and analysi
radar_pulse_freq
- 对雷达的脉冲全景图部分进行编写的DSP程序,主要使用Ｃ语言实现的算法 -Panorama of the radar pulses DSP program written in part, the main algorithm using C language
cemc
- 检测脉冲数目，实现速度检测，这个文件提供了三种方法-The number of detected pulses, to achieve speed test, this file provides three methods
YCMoter
- 利用IO口直接控制摇床电机，对IO口所发脉冲进行计数，达到摇床电机所需控制。-IO ports using the direct control of shaker motor, issued on the IO port to count pulses to achieve the required shaker motor control.
cesu
- 测量转速，使用霍尔传感器，被测轴安装有12只磁钢，即转轴每转一周，产生12个脉冲，要求将转速值（转/分）显示在数码管上。-Measurement speed, the use of Hall sensors, the measured magnetic steel shaft 12 is installed, the shaft per week to produce 12 pulses, requested speed value (
LCD_freq
- 功能：简单的频率计，可以配合fpga来技术脉冲数量，从而测频率-Function: simple frequency meter, can match the number of pulses fpga to technology to measure the frequency
robot
- 舞蹈机器人步进机仿真，C51程序通过，8步式步进电机脉冲序列，-Dance robot stepper machine simulation, C51 program through, 8-step sequence of stepper motor pulses,
jishuqi
- 计数器1，记满4个脉冲后，T1转为定时模式，定时时间为400毫秒，且通过P1.1引脚输出周期方波-Counter 1, note the full four pulses, T1 into regular mode, regular time is 400 ms, and cycle through P1.1 pin square wave output
Anemometro
- A airflow counter who works with PIC16F873a, uses the CCP1 to convert pulses im speed.
bjdj
- 1.步进电动机有三线式、五线式、六线式三种，但其控制方式均相同，必须以脉冲电流来驱 动。若每旋转一圈以20 个励磁信号来计算，则每个励磁信号前进18 度，其旋转角度与脉冲数成 正比，正、反转可由脉冲顺序来控制。 2.步进电动机的励磁方式可分为全部励磁及半步励磁，其中全步励磁又有1 相励磁及2 相励 磁之分，而半步励磁又称1-2 相励磁。图为步进电动机的控制等效电路，适应控制A、B、/A、 /B 的励磁信号，即可控制步
solve_the_problem_of_interference_pulses
- 解决实际采集数据时系统出现的难以解决的脉冲干扰的问题-Collecting data to solve real-time system appears difficult to solve the problem of interference pulses
led1
- PIC16F84 This program pulses port B bit 0 with a delay between each update -PIC16F84 This program pulses port B bit 0 with a delay between each update
PICDriver
- Source code of PIC 16F687 Microcontroller for controlling Bipolar stepper motor with LMD18245 driver over STEP/DIR pulses.