搜索资源列表
saa7120DDKBoard
- SAA7120开发板的资料，包括开发板原理图和寄存器说明-SAA7120 development board, including the development board schematic and registers descr iption
1_2
- 点亮PORTD口上所有的灯，要求定义状态寄存器地址，端口的数据寄存器地址和方向寄存器地址-PORTD I lit all the lights, require the definition of status register address, port data register address and register address direction
1_3
- 在程序中调用软件延时程序的点灯程序，要求定义状态寄存器的各种参数。-In the procedure call software delay proceedings even to light lamps procedures, require the definition of various parameters of the state of registers.
1_4
- 程序中调用定时器TMR0实现的延时程序完成点灯程序，要求定义端口的数据寄存器地址等基本参数。-Procedure call latency timer TMR0 realize the process is complete lighting procedures, require the definition of port data register address of the basic parameters.
simulate
- 循环冗余校验CRC (Cyclic Redundancy Check)码是由分组线性码的分支而来，其主要应用是二元码字。编码简单且误判概率很低，在通信系统中得到了广泛的应用。循环冗余校验码是属于分组码中的一类重要的线性码，它不仅在理论上具有很好的代数结构，而且其编码和译码可以通过线性移位寄存器很容易地实现。 通过对CRC的分析和基于MATLAB工具的仿真，充分证明了CRC的检错能力很强，编码简单。 -Cyclic Redunda
Serial_CRC
- CRC校验串行实现方法,verilog源码,利用反馈线性移位寄存器的方法,实现简单,适用于串行通信协议中的CRC校验.-CRC checksum method of serial realize, verilog source code, the use of linear feedback shift register method, the realization of simple serial communication pro
i2c
- ARM7的I2C读写，老外写的 很不错 如果在别的芯片上跑 要该寄存器-ARM7-I2C read and write, a foreigner writing is pretty good if the other chip to run to the register
ATPC_INSIDE_OUT(ARM-THUMB_Procedure_Call_Standard)
- 在arm编程的调试中经常碰到函数调用的规范问题，在函数调用中寄存器 的使用与分配是如何进行的，一个结构体是如何传递的，我们应该怎样写汇编函数才能符合函数调用的规范。这篇文章很好的阐释了这个问题。ATPCS（The ARM-THUMB Procedure Call Standard）的解释的ppt，容易懂，不要错过哦。-err
atmega_uart1
- 适用于ATmega16的串口程序。完成寄存器的初始化设计-ATmega16 Serial applicable procedures. Completion of the initialization register design
m_series
- 用移位寄存器产生M序列的MATLAB软件实现-M generated using shift register sequences MATLAB software
PIC-read-and-write-SPC3-ram
- PIC芯片读写SPC3寄存器的程序,PIC芯片不支持外部存储器扩展功能，通过软件编程，实现读写外部存储器功能。-PIC chip to read and write registers SPC3 procedures, PIC chip does not support external memory expansion capabilities, through software programming, to achieve rea
PWMwave
- 凌阳单片机脉冲控制DC 利用单片机的定时器和寄存器进行占空比设置，控制直流电机的电枢电压-Sunplus Singlechip DC pulse control the use of single-chip timer and register set up to carry out the duty cycle, control DC motor armature voltage
24C04zjdx
- MSP430FE427单片机下关于FM24C04寄存器字节读写的源码，已通过调试，很实用的。-Singlechip MSP430FE427 register under FM24C04 byte read and write on the source, has passed through debugging, it is practical.
LCM_0506
- 杭州qingda光电5.6吋256色液晶屏的C51控制程序，硬件采用的是直接读取寄存器地址的方式。-Hangzhou qingda photoelectric 5.6-inch color LCD screen 256 of the C51 control procedures and hardware used is a direct way to read register address.
LCM_C51_indirect
- QingDa光电5.6吋彩色液晶屏的C51控制程序。 硬件采用的是寄存器选通的间接控制方式！-QingDa photoelectric screen 5.6-inch color LCD of the C51 control procedures. Hardware used is register indirect gating control mode!
TMS320x280x__(ADC)
- 2812的ad的详细说明，包括精度、寄存器等，对大家在配置文件和制板都是很有用的-2812 A detailed descr iption of the ad, including the accuracy, registers and so on, for everyone in the configuration file and system board are very useful
372A
- 372A 读写操作子程序 read 为读372A内部寄存器子程序，将 0-Fh 寄存器内容读到CPU内部RAM 10H-1FH。 write 为写内部寄存器子程序，r7中放需改写的寄存器地址,r6中放需写入的数据。-372A subroutine to read and write operations for the time read the internal register subroutine 372A, 0-Fh
nRF905-regdefine
- 最完整的nRF905配置寄存器宏定义，经调试一点问题都么有！放心下载！-The most complete configuration register nRF905 macro definition, as debugging problems that you have! Download assured!
reg.h
- OMAP5912的DSP的寄存器映射，让大家省点时间吧。-OMAP5912 mapping of the DSP
ModbusProtocalManuel
- 标准MODBUS通讯规约的介绍包括功能码寄存器类型-MODBUS communications standards including the introduction of the Statute Function Code Register Type