搜索资源列表
0141
- 一个数字时钟的程序 ※※※※※※※※※※※※※※※※※ ※资料提供:上海齐济电子有限公司※ ※联系电话:21-65630199 ※ ※※※※※※※※※※※※※※※※※ 16F877秒表源程序,带注解 该源程序已在实验板上调试通过,读者可直接引用,并可以利用软件编程的灵活性,加以拓展,实现更为复杂的功能。-a
alarm_ok_1
- 用ATmega16实现的多功能带音乐闹铃(老鼠爱大米)的数字时钟,有3个功能键设置。具体功能为:秒表计时,闹铃音乐,时钟,校时设置。可以学习状态机的编程思想。-ATmega16 achieve with the music with multi-function alarm (Lao Shu Ai Da Mi) digital clock, There are three function keys installed. Specifi
MIAOBIAO
- 数字秒表 计时范围0~59‘59.9 分辨率0.1s 用数码管显示 秒表有一个按键开关-Digital stopwatch range from 0 to 59' 59 .9 0.1s resolution digital display stopwatch with a key switch
Second_Counter
- 这是一个四位的数字秒表,精确到0.01秒,三个按键,三个按键,一个复位,一个开始,一个停止,在Digilent的basys2开发板上运行,只须修改ucf约束即可在其他FPGA开发板上运行。-This is a four-digit digital stopwatch, accurate to 0.01 seconds, three buttons, three buttons, a reset, a beginning, a stop,
module-dapeng
- 本代码基于FPGA实现了计时范围:00’00”00 ~ 59’59”99,显示的最长时间为59分59 秒的功能。数字秒表的计时精度是10ms。显示工作方式:a、用八位数码管显示读数 b、用两个按钮开关(一个按钮使秒表复位,另一个按钮控制秒表的启动/暂停)-This code based on FPGA to realize the timing range: 00 00 00 ~ 59 59 "99," according t
stopwatch
- 设计一个数字秒表,共有6位输出显示,分别为百分之一秒、十分之一秒、秒、十秒、分、十分-Design a digital stopwatch, a total of six output display, respectively, hundredths, tenths of a second, seconds, ten seconds, minutes
shuzimiaobiao
- FPGA开发实例 之 数字秒表.七段码管显示.秒表由于其计时精确,分辨率高(0.01秒),在各种竞技场所得到了广泛的应用。-FPGA development instance of digital stopwatch. 7 yards tube display. Stopwatch because its timing precision, high resolution (0.01 seconds), the income to th
dingshiqi
- 基于stm8s 定时器实现小灯闪烁 定时数字秒表 程序- Based stm8s small timer, digital stopwatch timing lights flashing procedure
MB
- 基于VHDL语言数字秒表设计,在FPGA实验平台下开发-Digital stopwatch design based on VHDL, FPGA experimental platform under development
sport
- 基于FPGA的数字秒表,通过按键开始计时,再次按下暂停,按下复位键清零-FPGA-based digital stopwatch, through the button to start timing, press pause again, press the reset button clears
test
- 基于FPGA的数字秒表(数码管扫描)程序。 平台:quartusII 15.0-FPGA-based digital stopwatch (digital scan) program. Platform: quartusII 15.0
timer
- 数字秒表,按键+数码管 上电后数码管开始计时,精度1/10秒: 按 SW2 :复位(清零后重新计数) 按 SW3 :暂停 按 SW4 :继续计数-Digital stopwatch, key+ digital tube after power digital control start timing, precision 1/10 sec: Press SW2: Reset (after a re-count is cl
stopWatch
- 基于VHDL语言数字秒表的实现!使用模块化的设计,包含详细设计说明文档。可在DE2-115开发板上进行验证!-digital stop watch based on VHDL language
time
- 单片机程序,数字时钟,时分秒均可调节,可一键暂停或启动或复位,带dsn设计图,可直接仿真。(Microcontroller programming, digital clock, minutes and seconds can be adjusted, can be a key to start or pause or reset, with dsn design, direct simulation.)
szmb
- 用VHDL语言基于ISE,在XILINX FPGA开发板上编写的数字秒表程序(Using VHDL language, based on ISE, in the XILINX FPGA development board prepared by the digital stopwatch program)
miaobiao
- Cyclone V开发板实现数字秒表功能,带有启动,暂停,复位功能。可以显示小时,分钟,秒。(Cyclone V development board implements digital stopwatch function, with start, pause, reset function. It can be shown hours, minutes, seconds.)
StopWatch
- 利用Verilog实现数字秒表(基本逻辑设计分频器练习) 设置复位开关。当按下复位开关时,秒表清零并做好计时准备。在任何情况下只要按下复位开关,秒表都要无条件地进行复位操作,即使是在计时过程中也要无条件地进行清零操作。 设置启/停开关。当按下启/停开关后,将启动秒表输出,当再按一下启/停开关时,将终止秒表的输出。 采用结构化设计风格描述,即先设计一个10分频电路,再用此电路构建秒表电路。(Using Verilog to real
基础1.2及综合1.3代码
- 使用8086制作数字秒表,实现计时功能,可以定时(The 8086 descr iption, combined with LCD12864, shows the size of the ad transformation)
基础5.6代码
- 使用8086制作数字秒表,实现计时功能,可以多吃使用(The 8086 descr iption, combined with LCD12864, shows the size of the ad transformation)
clock
- 在C51单片机上实现了数字钟功能,以及六种其他功能,包括日期显示、秒表、定时器、闹钟等(通过按键切换)。(The function of digital clock is realized on C51 microcontroller, and six other functions, including date display, stopwatch, timer, alarm clock and so on.)