搜索资源列表
aaaa
- 曼彻斯特编码的接收这几天没事弄了一个曼彻斯特编码方式的接收程序,给大家分享-Manchester encoding receiver these days nothing to get a Manchester encoding of the receiving program for everyone to share
mancodec
- 曼彻斯特编码器与译码器 FPGA嵌入式项目开发-mancodec fpga
graphing
- 1100011001的非归零码、曼彻斯特编码、差分曼彻斯特编码、调幅(ASK)、调频(FSK)和调相(PSK)的编码波形示意图-1100011001 of the NRZ, Manchester encoding, differential Manchester encoding, AM (ASK), frequency modulation (FSK) and phase modulation (PSK) waveform diagr
manch
- 该文件是一个完整的工程文件,用VerilogHDL语言编写,包括曼彻斯特编码器的设计文件和仿真测试文件以及解码器的设计文件和仿真测试文件。在Modelsim中仿真测试通过。-The document is a complete project file, with VerilogHDL languages, including the Manchester encoder design documents and simulation
Manchester
- 用matlab实现的曼彻斯特编码。50 占空比(可调)。绘制时域波形和频域功率谱密度。结果跟北邮的郭文斌的通信原理课件上的形状一模一样。-Manchester encoding with a matlab implementation. 50 duty cycle (adjustable). Draw time-domain waveform and frequency domain power spectral density. T
Manchester_codec
- 曼彻斯特编解码器,本程序实现模拟MIL-STD-1553B总线上的数据格式-Manchester codec, the procedure for analog MIL-STD-1553B bus data format
bishe6
- 基于VHDL的曼彻斯特编解码的设计程序及仿真波形-Manchester code
47651501MillerCode
- 曼彻斯特编码的MATLAB实现,做了好久的,大家一看就能明白-Manchester encoding MATLAB implementation, so a long time, and we can see a glance
Manchester
- 使用C语言编写的曼彻斯特编码和解码功能函数-Written in C language with Manchester encoding and decoding functions
manchester
- 该程序主要是完成曼彻斯特码的,编码,同步,加噪,译码,计算误码率等功能。-the program main contain manchester code, synchronization, add the gauss noise and so on
hdlc_rs
- 一种带有CRC校验、一次可连续发送1-15块16字节数据、带有曼彻斯特码的hdlc收发程序,在Altera中仿真并在实际芯片中试验过的程序-One kind with a CRC check, send a continuous block of 16 bytes of data 1-15, with Manchester' s hdlc receive procedures in the Altera chip simulati
mcsdte
- FPGA嵌入式项目实战,曼彻斯特编码器与译码器-FPGA embedded project combat, Manchester encoder and decoder
verilog_Manchester
- 曼彻斯特码编码电路,在工业电路中有较好的抗干扰性,而且编码电路简单,容易在FPGA上实现-Manchester encoding circuit, the circuit in the industry in a better anti-interference, and the coding circuit is simple, easily implemented on FPGA
manchesitecode
- 基于pic单片机实现曼彻斯特编码解码实例程序-Manchester-based MCU pic codec sample program
man
- 基于曼彻斯特编码的论文,适用于无线通信的编码方法-Paper-based Manchester encoding for the coding method for wireless communication
manchester
- 源码包含三个模块,数据发送模块是读取FIFO中的数据后,将并行数据转换为串行,同时对串行数据进行曼彻斯特编码输出。数据接收模块是对接收的数据进行曼彻斯特解码。FIFO控制器模块将接收的串行数据转换为并行,并存储。 曼彻斯特解码部分本文采用了过采样技术,使用了一个8倍时钟进行采样。每一个数据周期采样8次,每四次采样确定一个状态,如果采样到三次及以上高电平则认为是高状态,否则认为是低状态。状态由高到底则是数据0,由低到高则是状态1。-S
scan_and_tx
- 模拟rfid的曼码发送接收,使用了c51单片机,对曼彻斯特码发送接收的理解有非常好的帮助(RFID transmission and receive)
m_manche
- 有关于M序列的曼彻斯特编码,亲自验证有效。(The Manchester code of the M sequence is personally validated.)
RC_A9139
- 比较高效的低功耗高频接收,译码,解码曼彻斯特。常开模式可以达到3.8mA以下(High efficiency, low power, high frequency reception, decoding, decoding, Manchester. Normally open mode can reach below 3.8mA)
manchester
- 曼彻斯特码的编码和解码程序,在ISE软件上可以成功实现(Manchester code encoding program can be successfully implemented on ISE software)