搜索资源列表
c8051f300chongdian
- 基于c8051f300设计的锂电池充电器的应用笔记。内有源代码和原理图-C8051f300 design of lithium-based battery charger application notes. Within the source code and schematic
NickelCadmiumandNickelHydrideBatteryChargingApplic
- HT48R062 在镍氢、镍镉电池充电器中的应用-Nickel Cadmium and Nickel Hydride Battery Charging Applications Using the HT48R062
ni-mhcharge
- 镍氢电池详细的充电方法以及C代码,不错的文章.-Ni-MH battery charging methods and the detailed C code, a good article.
main
- PIC10f220 完成的电池充电保护 -PIC10f220 complete battery charging protection
Ni-mH_battery_charger
- 镍氢电池充电器方案，含汇编程序，来自ATMEL-Ni-mH battery charger solution, include assembly firmware
batterycharge
- 通过单片机程序控制对电池分时充电，并通过热敏电阻实时测温，防止电池充电过程过度发热-MCU programmed by time-charging the battery and, through the thermistor temperature measurement, battery charging process to prevent over-heating
EUP8054ver1.0
- 单节锂电池充电芯片手册 EUP8054 PDF文件-EUP8054 datasheet
CodeCharger
- 共享我自制的充电器程序，此程序可以控制我的四节电池充电， 内部算法适用于小容量的锂电池充电-I share my home-made charger program, this program can control my four batteries, the internal algorithm is suitable for small-capacity rechargeable lithium battery
595643732051
- 充电程序，充满后转为涓流充电，每月分钟表对电池检测一次。
code
- 主要用于单节锂离子电池充电控制，采用美信半导体公司得锂电池充电芯片，其工作原理如下：有电池插入时，LED亮，蜂鸣器发出提示音，系统进入充电。-Mainly used for single cell Li-ion battery charge control, the use of Maxim Semiconductor chips have lithium batteries, it works as follows: a batter
Second
- 使用在锂电池充电器上的材料，包括采集等信号处理-Lithium battery charger used in the material, including the collection of signal processing, etc.
chongdian
- 用matlab/simulink搭建的铅酸蓄电池充电模型。-Using matlab/simulink model to build the lead-acid battery charging.
LED电池充电控制
- 用于LED灯具，用松翰单片机控制，点亮，和充电控制
android电池管理
- BatteryService作为电池及充电相关的服务： 监听Uevent、读取sysfs里中的状态、广播 Intent.ACTION_BATTERY_CHANGED(BatteryService Uevent sysfs Intent.ACTION_BATTERY_CHANGED)
Battery_Charging_Discharding_model
- 电池充放电MATLAB模型()
bq24196
- TI最新优化充电IC，充电电流大，可以I2c通讯，对锂电池充电做管理。(TI latest optimization charging IC, charging current, you can I2c communication, lithium battery charging to do management.)
充电盒
- MCU外加简单的电路即可完成对耳机充电功能。 多重保护 充/放电电池端的过压、过流保护，放电转换效率高(The MCU has a simple circuit to recharge the earphones. Multiple protection Overvoltage and overcurrent protection at charge / discharge battery end, high disch
电动汽车电池充放电simulink仿真模型
- Simulink搭建的电动汽车充电机模型，可用于研究电动汽车充电产生的谐波问题(Simulink's electric vehicle charger model can be used to study the harmonic problems caused by electric vehicle charging.)
锂电池充电曲线说明
- STM32F103的PID通用算法，电源 充电例程(STM32F103 PID general algorithm, power charging routine)
lidianchi_190322
- 锂电池模型，这个模型可用于锂电池充电和放电的仿真，输入充放电电流，即可输出端电压和开路电压(This model can be used to simulate the charging and discharging of lithium batteries. The input charging and discharging current can be used to output terminal voltage and op