搜索资源列表
周期三角波双边脉冲频谱
- 通过周期三角波双边脉冲频谱来实现周期三角波双边脉冲-cycle through bilateral triangular pulse wave spectrum to achieve bilateral cycle triangular wave pulse
用FFT分析周期矩形脉冲及其频谱
- 用FFT分析周期矩形脉冲及其频谱, 这是计算周期矩形脉冲双边频谱的程序。-using FFT analysis cycle and rectangular pulse spectrum, which is calculated cycle rectangular pulse spectrum of bilateral procedures.
单脉冲启动报警
- 单脉冲启动报警,8253的记数功能,8255接口,报警实现用红灯五圈,绿灯五圈来提示。-monopulse alarm activated, the entry number 8253 features 8255 interface, alarm achieve five laps with a red light, green five laps to suggest.
键盘设计
- 1,消除按键的抖动问题 因为按键在闭合或断开过程中出现一段抖动期,主要由于按键的不稳定性引起的,这时会呈现一串页脉冲,时间的长短和开关的机械特性有关。一般在5ms~10ms之间。为保证CPU对键的一次闭合作一次处理,必须去抖动。在键的稳定闭合或断开时读键的状态。 2,据EICE51原理图编写并调试一个键输入子程序,其功能为判断键盘上有无键输入,若有键入,作去抖动处理后,计算输入键的键号送累加器A。-eliminate jitter bu
t2t3t4
- c8051f040 t3频率方波输出,T4脉冲计数,T2计时例程-c8051f040 frequency square-wave output, pulse counting T4 and T2 time routines
pulse_change
- 用vhdl实现脉冲宽度可控的一简单程序 仿真环境MAXPLUS--use VHDL to achieve controllable pulse width of a simple process simulation environment Segments-
占空比和频率
- 用ATMEL公司的S52内部定时器测量脉冲频率,范围从0.5Hz到30KHz,该程序已经调试成功,可以直接运用。-ATMEL Corporation with the S52 internal timer pulse measurement frequency range from 0.5 Hz to 30KHz, the debugging procedure has been successful, can be directly
gaussplot
- 高斯脉冲及高斯一阶导、高斯二阶导产生时域图-Gaussian pulse and a Gaussian derivative, Gaussian, when the second derivative domain plan
hicj6
- 这是一个,51单片机的脉冲采集器的程序,可以用KEIL C环境下编译,也可以使用WAVE软件,运行非常稳定-This is one of 51 single-chip pulse collector procedures, can be used KEIL C compiler environment, you can also use WAVE software, to run very stable
用窗函数法设计FIR滤波器
- 用矩形窗、三角窗,汉宁窗,海宁窗等多种窗口设计有限长单位脉冲响应滤波器-with rectangular windows, triangular windows, Hanning window, multiple windows Haining window design finite impulse response filter units
sdq
- 用loop51实现的可调式脉冲发生及检测器,可以手动输入所发生脉冲的频率和占空比,实时检测及动态显示-loop51 achieved with adjustable pulse and the detector, which can occur manually input pulse frequency and duty cycle, real-time detection and dynamic display
Boost_PWM
- matlab中的simulink对boost电路和PWM脉冲产生的仿真设计程序-of Matlab Simulink right boost PWM pulse circuit and the simulation design process
脉冲记时CPLD
- 工作原理: 脉冲输入,记录30个脉冲的间隔时间(总时间),LED显示出来,牵涉到数码管的轮流点亮,以及LED的码。输入端口一定要用个 74LS14整一下,图上没有。数码管使用共阴数码管。MAXPLUS编译。 测试时将光电门的信号端一块连接到J2口的第三管脚,同时第一管脚为地,应该与光电门的地连接(共地)。 开始测试: 按下按键,应该可以见到LED被点亮,指示可以开始转动转动惯量盘,等遮光片遮挡30次光电门后,
智能计时计数器
- 智能计时计数器 有计两脉冲间隔时间、几脉冲间隔时间、30秒脉冲数等,还有就是根据这些时间做一些运算,51,牵涉到LCD,汇编C混合,计时器的使用。 本人首个正式产品,各位兄弟见笑了。原理图、程序、图片都有。-counter a smart time or two pulse intervals, pulse several time intervals, 30 seconds pulse, and so on. There is
muxplusii --vhdl 经典程序
- 用VHDL编写的数字时钟,可变宽度脉冲产生器-prepared using VHDL digital clock, Variable width pulse generator, etc.
PCM_Testing
- PCM(脉冲编码调制)在MATLAB中仿真调试的程序-PCM (pulse code modulation) in MATLAB simulation testing procedures
8051_timer0_pulse
- 8051系列单片机的利用定时器进行脉冲宽度测量的c语言的简单的操作例程-8051 for the use of timer pulse width measurement of the C language routines simple operation
uwb_ppm
- 该程序仿真超宽带的脉冲位置调制。是在MATLAB下实现的。-ultra-wideband pulse position modulation. MATLAB is achievable.
pulse-VHDL
- 可控脉冲产生VHDL程序 开发软件ISE,程序通过了器件后仿真并在芯片XC9572中实现了-controllable pulse generated VHDL ISE software development procedures, procedures adopted after the simulation devices and chips to achieve the XC9572
keyboard_input_v1.02
- matlab键盘输入模型程序,用simulink制作。在7.0以上版本直接运行 运行过程中按一下键盘就会看到示波器上出现一个脉冲信号。-Matlab keyboarding model procedures used Simulink production. In version 7.0 to run over the course of operation under the keyboard will see what appe