搜索资源列表
19-TMR1-Counter-LT-10000
- 用工作于计数方式的TMR1实现按键或脉冲计数，每按键一次记录为1，可以累加和复位。-With the work in the way of counting the TMR1 key or pulse counting, every button once for a record 1, can be accumulated and reset.
jishu
- 光电编码器4倍频脉冲计数，绝对实用，其中包括A B正转计数和 A B 翻转计数 精度准确-4x optical encoder pulse count
tim1
- stm8s tim1外部时钟源模式2 对外部脉冲计数 -stm8s tim1 external clock source for external pulse counting mode 2
Pulse-detection-of-eight-channels-
- 八路脉冲计数程序，用于对外部脉冲进行计数的程序。-Pulse detection of eight channels.
tongxinwang
- 通信网试验基础实验代码，包括时间表调度实验、摘挂机检测实验、脉冲计数实验、位间隔识别实验、软件送音实验、驱动交换网络实验-Communication network based experimental test code, including the timetable scheduling experiment, hook detection experiments, pulse-counting experiments, the
VHDL_ReversibleCounter
- 可逆计数器(两位十六进制,以十进制方式显示即从00,01数到14,15然后00,01再到根据10hz晶振(低频都可选,视板子情况而定)作为时间脉冲计数,rst键可以重置(清零 )计数器,drct键选择加法计数还是减法计数.-2-bit-Hexadecimal Reversible Counter(decimal display)
dma
- 该程序是基于飞思卡尔公司K60为主控芯片，用于多路脉冲计数功能的程序，DMA计数能够不占用主控芯片资源，这样能够提高程序的运行速度-The program is based on the freescale company K60 as main control chip, program for multi-channel pulse counting function, the DMA count to take up the ma
c-pulse
- 利用脉冲计数测量汽车变速器输入、输出轴转速-Automobile transmission measurement using pulse counting input and output shaft speed
LS7266R1_cn
- 正交脉冲计数芯片的中文说明，适合三相电动机，绞车等对两路正交脉冲信号进行加减计数的应用-Quadrature pulse counting chip Chinese explanation for three-phase motors, winches, etc. on two orthogonal pulse signal subtraction counting applications
codes
- 信号发生器的频率测量，主要是运用单片机的外部中断计数器对方波信号的进行脉冲计数实现。 内部定时器T0设定外部计数器的计数时间t，在t时间到达是从外部计数器读出计数的脉冲个数n， 从可以根据t和n计算出信号的频率。 -Frequency measurement signal generator, mainly using MCU external interrupt counter counts each pulse wave
jiulong
- 控制纺纱机的单片机程序。对脉冲计数，并显示卷布的数值。-Control spinning machine microcontroller program. Pulse count and display the value of the volume of cloth.
j
- 编码器脉冲计数程序，采集固定脉冲，计时来计算脉冲周期-The encoder pulse counting procedures, collecting a fixed pulse timing pulse period is calculated
Yujinbiao_TemplateTIM2_CH1_ETR_004
- 功能： 1芯片STM32F103RET6。 2timer1_ETR PA12 第45脚和timer3_ETR PD2 第54脚作为外部脉冲输入，以此来记录脉冲的个数。 3timer4 实现定时，每500ms读取一次脉冲个数即半个周期的脉冲个数，来验证脉冲计数是否正确。 硬件实验证明程序OK.-STM32 external clock input pulse counting code ETR
freq_Test_STC
- 本程序通过外部中断1与定时器1实现对外部方波信号频率测定，外部测试信号接外部中断1管脚，下降沿触发中断对脉冲计数，定时器1用作定时对外部信号频率测试。测试结果在8位数码管上显示。本程序已经在电机转速测试项目中应用，精度比较高，具有很好的实用价值。-the program is used to measur the pulse frequency on the platform STC12C5A60S2,and dispaly the
pulse-counting-32-bit-MCU
- 此代码是基于32位单片机的脉冲计数程序代码，能兼容常用的STM32和比赛用的飞思卡尔K60等32位单片机！-This code is based on pulse counting of 32-bit MCU program code, can be compatible with commonly used STM32 and competitions with freescale K60 32-bit MCU!
frequency-measure
- 基于stm32rbt6的频率测量程序，用外部脉冲计数模式，能测1Hz到32Mhz，精度较高-Based stm32rbt6 frequency measurement procedures, external pulse counting mode, can measure 1Hz to 32Mhz, high precision
TEST
- 用定时器0工作于方式1来实现脉冲计数并请0-Timer 0 in the way to achieve a pulse count and invited 0
the-FPGA-taxi-billing-program-
- 出租车计费的硬件设计分为5个模块：1.车轮脉冲计数模块；2.里程计数模块；3.计费模块；4动态扫描模块；5译码模块-The taxi billing hardware design is divided into five modules: 1. The wheels pulse counting module 2. Mileage counting module 3. The billing module 4 dynamic s
encoder_V3.6
- 在STM32F103RBT6上编写的检测增量型编码器的范例。已测试，能用。4000个脉冲计数，如有需要更大的脉冲上限可自行修改。-An example of a detection incremental encoder written on STM32F103RBT6. Has been tested, can use. 4000 pulse counts, such as the need for a greater pulse l
mapancesu
- 采用单片机控制码盘测速，能够对码盘实时速度进行脉冲计数，并且附有原理图-Controlled by single chip microcomputer and speed of encoder real-time speed pulse counting, and schematic diagram attached