搜索资源列表
使用直接序列扩频芯片SX043实现高增益扩频Modem
- 使用直接序列扩品芯片SX043实现高增益扩品的设计方案和原理图-Direct Sequence Spread use goods chip to achieve high gain SX043 expansion goods design and schematics
增益控制
- 基于可编程控制器的增益控制
开关电源环路增益测试
- 开关电源环路增益测试.pdf
自动增益控制放大器设计
- 自动增益控制放大器设计
C4.5算法源程序
- C4.5算法进行决策树生成 以信息增益最大的属性作为分类属性,生成决策树,从而得出决策规则。-C4.5 decision tree algorithms to generate information gain the greatest attribute as a classification attributes, generate decision tree, and came to decision-making rules.
图4-2-6矩形截断低通滤波器的增益特性
- 用matlab观察矩形截断低通滤波器的增益特性-using Matlab observation rectangular cut-off low-pass filter characteristic Gain
使用直接序列扩频芯片SX043实现高增益扩频Modem
- 使用直接序列扩品芯片SX043实现高增益扩品的设计方案和原理图-Direct Sequence Spread use goods chip to achieve high gain SX043 expansion goods design and schematics
pathloss&gnoise
- cp0801_pathloss为UWB信道损耗计算函数,利用a=(c/(d^gamma))计算出信道增益,然后对函数的输入信号幅度进行变换得到输出结果。 cp0801_Gnoise1和cp0801_Gnoise2为产生AWGN的函数,分别为Eb/No和Ex/No条件下AWGN的产生-cp0801_pathloss for UWB channel depletion calculation function, use a = (c/(
agc3
- c语言编写的对语音进行自动增益控制的程序,输出电平可由参数调节 -the right voice for automatic gain control procedures, output level adjustment parameters can be
RSSI_contr
- VerilogHDL.自动增益控制模块中产生控制电压的部分-VerilogHDL. Automatic Gain Control Module have some control voltage
voice_agc
- 在C54X DSP 下写的,DSP接收PC机话音数据,并在DSP内对话音作AGC自动增益控制!-under the C54X DSP wrote, DSP receiving PC voice data, and the DSP for voice within the AGC AGC!
ID3code
- id3算法进行决策树生成 以信息增益最大的属性作为分类属性,生成决策树,从而得出决策规则。id3的源码决策树最全面最经典的版本.id3决策树的实现及其测试数据.id3 一个有用的数据挖掘算法,想必对大家会有所帮助!-id3 decision tree algorithms to generate information gain the greatest attribute as a classification attributes,
TCM-16QAM
- 网格编码的16QAM仿真,验证网格编码的增益和误码-grid coding 16QAM simulation, verification grid coding gain and the error
DSPMcBSP
- 本实验讲述了与多通道缓冲串口(McBSP)相关的寄存器的含义,并通过在DSP系统中实现音频扩放系统的自动增益控制(AGC)算法这个例子了解多通道缓冲串口的应用。-about this experiment with multi-channel buffer serial port (McBSP) related to the meaning of the Register, and through the DSP Audio Syste
ADC
- 有关语音的滤波以及自动增益控制电路的原理图以及PCB图
InformationGain
- 信息增益C++程序,用于计算变量之间包含分类信息,数值采用连续值-Information gain C++ Procedures used to calculate the variable that contains classified information between the numerical value of the use of continuous
BigTree2
- 该代码是数据挖掘里面的决策树算法 利用ID3理论,通过对训练数据的分析判断,计算出各个数据的其它对目标属性的重要程度,即计算出每个其它数据的信息增益值来将训练数据逐步分类,最后得出目标分类,从而实现决策树的生成过程。最后即可利用此决策树来对新的数据进行测试,判断其目标属性的可能值。-The data mining code is inside the ID3 decision tree algorithm using the theo
AGC
- 自动增益控制Verilog编程,本程序开发环境为xilinx ISE7.1-AGC Verilog programming, the program development environment for the xilinx ISE7.1
基于模糊切换增益调节的滑模控制
- 基于模糊切换增益调节的滑模控制,通过模糊控制算法调节切换增益,实现消除滑模控制的抖振。(The sliding mode control based on fuzzy switching gain regulation is adopted, and the switching gain is adjusted by fuzzy control algorithm to eliminate chattering of sliding m
耦合电感倍压单元高增益变流器拓扑形成方法研究
- 该文档为一篇硕士论文,研究了一种高增益的耦合电感电路(This document is a master's thesis, and studies a high gain coupled inductor circuit.)